days agoLynn, MA+16 milesAuto Parts for Sale
This is a 5 page article on the review of the upcoming 1983 Rabbit Gti. This is NOS and a reprinted extract from Car and Driver for promoting the upcoming Gti in VW Dealerships back in 1983. This is a must have for any Gti collector. Let me know if you have any questions. $13 shipped in the lower 48 states. PayPal and US Postal money order accepted. Thanks, Jim
nice clear face, needle bounce smooth. 3-1/4 mounting hold $135 shipped
nice 4k tack. 3-1/4 mounting hole. $125 shipped
days agoLynn, MA+16 milesAuto Parts for Sale
This is a 5 page article on the review of the upcoming 1983 Rabbit Gti. This is NOS and a reprinted extract from Car and Driver for promoting the upcoming Gti in VW Dealerships back in 1983. This is a must have for any Gti collector. Let me know if you have any questions. $13 shipped in the lower 48 states. PayPal and US Postal money order accepted. Thanks, Jim
removed from a 53 mercury about 20 yrs. ago and taken apart and stored inside, have all parts , main case, tail shaft housing, flywheel, torque converter and all internal parts, good for parts or to rebuild, Hollander book says it fits 53-54 Ford & Mercury $50.00 NO SHIPPING
removed from a 53 Mercury about 20 yrs ago and taken apart and stored inside, have all parts, main case, tail shaft housing, flywheel, torque converter and all internal parts, Hollander book says fits 53-54 ford & mercury $50.00 NO SHIPPING
I have a gently used stainless steel cat back exhaust from TT. For a 1991 Gli 2.25 $300 shipped. Thanks!
I have a gently used stainless steel cat back exhaust from TT. For a 1991 Gli 2.25 $300 shipped. Thanks!
59 A/B Ford Flathead engine, short block/no heads, includes distributor, intake & exhaust manifolds, oil pan, water pumps, motor mounts, lower crank pulley, new exhaust seats & cam bearings in the box, has Ford rebuild tag as shown, turns free, great rebuildable core, inside storage for over 40 + years, $295.00.
days agoLynn, MA+16 milesAuto Parts for Sale
This is a ten page sales catalog on the 1989 Fox featuring nice shots of the wagon and sedan. $13 for one or $20 for two shipped in the lower 48 states. Otherwise, email for a shipping quote. It will be shipped securely with cardboard and in a bubblewrapped envelope. PayPal accepted. Thanks, Jim
Looking for a couple parts to finish the turbo build: -Walbro Inline Fuel Pump -#42 Injectors (Prefer green tops but will settle for green Giants) -C2 #42 chip -SRI -Intercooler (smaller size to stuff into MK2 without too much hacking) -4" MAF Housing Located in Dallas but will pay for shipping.
I managed to leave my tailgate down (complete moron) and lost all my rigging to my 06 Suzuki DF 250s. Need gauges and wiring harnesses. 4135305743 is my cell and easiest means of getting me. Thanks in advance
This is an interesting body panel. It is a rear valance for a late bay, the welded in, un-removable kind. The actual valance piece is the same size and fit as a German produced, late Baywindow bus, but the tin in front of it is for the Brazillian/ Mexican market buses that still had air-cooled engines until sometime in the 90s when they switched to water-cooled platforms. This would be useful i...
This is the late Baywindow LH (drivers side in US) rear wheel tub, complete piece, including seat belt mount and all the trimmings, captive nuts, and that pesky section that meets up with the outer fender skin most folks are replacing on a rusty bus restoration. There is a small channel that goes along the arch where seam sealer, or some type of rubber/ silicone sealer was used at the factory b...
Couple VERY nice quarter window glass pieces pulled many years ago from a 71 STD bug and stored. Nice and clean Sukurit pieces. No stickers or adhesive residue. Price is for the pair but I will sell individually for $10 if you just need one. I am willing to ship these, and I have the ability to pack them very well with foam and whatnot, but i cannot accept responsibility if this breaks in shipp...
Short side tie rod for 68+ Bettle. Ghia. OG VW tie rod ends, still usable. Unit was pulled to replace bent long side and replaced everything at once. Could use new boots if so inclined. _________________ I NOW TAKE PAYPAL PAYMENTS!! Huzzah!!! I ship UPS Ground as I am in charge of shipping at work. I am not paying UPS store rates so you won't get killed on shipping, and I can ship everyday Mon-...
Straight pulley half, dunno where the other half went. OG VW will clean up nice. See my other ads Pics/answers on request _________________ I NOW TAKE PAYPAL PAYMENTS!! Huzzah!!! I ship UPS Ground as I am in charge of shipping at work. I am not paying UPS store rates so you won't get killed on shipping, and I can ship everyday Mon-Fri, using only the best packing materials to make sure your stu...
Brandy new Guide collar/sleeve for a 71 up IRS transmission using the collar-less pressure plate/clutch combo. Still with the bag from Bug City, showing part number and price. See my other ads. Pics/answers on request. _________________ I NOW TAKE PAYPAL PAYMENTS!! Huzzah!!! I ship UPS Ground as I am in charge of shipping at work. I am not paying UPS store rates so you won't get killed on shipp...
Aftermarket horn, 12 volt. Worked when I pulled it to replace with an original. Pretty sure I have wire boots that will fit this that I will throw in if I can find them _________________ I NOW TAKE PAYPAL PAYMENTS!! Huzzah!!! I ship UPS Ground as I am in charge of shipping at work. I am not paying UPS store rates so you won't get killed on shipping, and I can ship everyday Mon-Fri, using only t...
1 stock sway bar for bug/ghia with the old bushings intact (useable). From a BALL JOINT beam. The one in the picture with some blue paint on it was pulled from a Ghia, the other from a bug. The Ghia bar is SOLD. The other one was pulled from MY bug in favor of a heavy duty EMPI bar. It is mis-shaped/slightly bent on one end but was installed and working on my personal car for many years with no...